Replace Lock in UPVC Door
A professional locksmith should be contacted if your upvc door locks aren't functioning properly. They are quick, efficient and complete the task to a very high standard.
Change the barrel lock of a Upvc barrel isn't that difficult to do. You only need to know what you need to do and follow the steps below.
Removing the Barrel Lock
Upvc windows and doors are typical in all kinds of houses. They are great for allowing sunlight into your home and are easy to open with the correct key. The process of changing the barrel on a uPVC door is a straightforward job that only takes five minutes. It's a quick fix if you've lost your key, or if a tenant has left and has not returned it, or the barrel of your lock is damaged.
The first thing you have to do is to take off the handle screws. This will allow you to move the handles out of the way to access the barrel screw for locking. Be replacing window locks not to loosen the screws too fast because it could damage the handles or cause them to fall off while you are working.
After the screws have been removed, locate the screw that holds the barrel lock in position on the inside of your door. This screw is distinct in color from the other screws on your door and sticks out. Utilizing the Phillips screwdriver, remove the screw. Next, take the present key that is used for the lock and put it in the barrel. Turn it to the right as far as you can. This should let the barrel loose and make it easier to pull out of the door.
Now that you have loosened the screw, it's time to break the pins that support the euro cylinder in place. To accomplish this, you'll need strong pliers or mole grips. Grab the protruding end of the euro cylinder and bend it from side to side and upwards and downwards. This will cause the support pins to break, thereby holding it in place.
Once the old cylinder is gone, you can start the process of installing the new one. To ensure you purchase the correct replacement, first measure the lock cylinder. This can be accomplished by measuring the distance from the center of the circular portion of the keyhole to the middle of the square spindle. The measurement must be taken from the upper spindle hole.
Changing the Cylinder
The euro cylinder is the principal locking mechanism for the door made of upvc. They are simple to replace and don't need an expert locksmith or handyman service. In fact, if the lock you have isn't anti-snap or anti-bump it is recommended to change it to one with this protection built-in. They are very affordable and could save you money as well as inconvenience if your locks have been damaged by these security threats.
Open the door and then stand in front of it. This allows you to reach the screws that hold the handle by hand or with the appropriate tool. You can loosen this screw a little bit maybe a quarter-turn to get started.
The cylinder will now be easily removed, as the screw will stop holding it in place. The next step is to decide what size replacement cylinder you require. There are approximately 25 sizes to pick from. You should bring your previous cylinder when you buy the new one to make sure it fits.
If you're not sure of the dimensions, measure from the screw hole center to the end of the cylinder. You can only be sure that you're buying the right sized cylinders to fit your upvc door by measuring from the center of the screw hole to the end of the cylinder.
Insert the new cylinder into your door the opposite way you removed the old one. The alignment of the lock cam can be a challenge, but it is generally a matter of alignment.
The next step is to insert the long screws for securing. After that, you are able to check that the cylinder is secured in the door. Then, you can attach the handle back to the door and then test it again. If all is well then your cylinder lock in your Upvc door has been replaced and you should have added another layer of security to your home.
Change the Handle
There are a variety of reasons a door knob or handle may become loose. It can be due either to the wear and tear on the handle or the square spindle within the handle. In this instance, the door handle will have to be replaced.
It is crucial that the door is opened so that it will not close between taking the handle off and replacing it. Remove the screws from the interior side of the handle plate with a screwdriver. This will release your handle from the plate. Do not lose these screws, because you will need to re-screw them later.
You can now take off the handles to gain access to the cylinder lock within the door. The cylinder lock is round or bulb-shaped and is only used for multi-point locks for upvc and some aluminum doors. It is similar to changing the handle. The only difference is that you'll have to remove the old cylinder from the door and replace it with a new one.
It is essential to consider the size of the handle replacement when selecting one. The handle should be of the same size as the original, since it will need to fit into the screws that hold the handle in place. You can start by consulting the table of sizes that lists the most common sizes of replacement handle plates as well as their keyhole centers.
Consider changing your handles for your upvc doors to a higher security standard like a Sold Secure SS301 set or 2* Kitemark security handles. This will improve the security of your home and make it easier to operate your door. These sets are slightly more expensive however the added security and peace mind is worth the cost. The constant need to push the handle of the door upwards and downwards to shut or open it is not something you would like to be doing.
Change the Lock
The security lock on your uPVC door could be a weak point for burglars. You might want to upgrade your uPVC door to a multipoint lock in order to ensure it is secure. This could include a deadbolt and an open hook to block intruders. A professional locksmith can assist you with this, however it is also possible to do the work yourself. You'll need some tools, but the process is simple and fast.
The first step is to loosen the screws that hold the handle in place. You can remove the screws with a screwdriver and put them in a secure place. You can then raise the handle and reveal the screw that is holding the cylinder in position. You can unscrew this screw and replace it with a new one. Make sure the screw is exactly the same size as the original. It should be aligned properly with the lock barrel.
Changing the lock of your uPVC door can be a challenge. It is essential to the security of your home. If you make a mistake, it could leave you unable to open the door. If you know how, it is relatively easy and costs less than calling an expert locksmith.
You'll need to remove the faceplate on the inside of the lock to change the lock. You will need to be able to see the screw on the inside of the door as well as the bolt that holds it on the outside of the door. Once you have access to these screws, you can remove the faceplate and replace the cylindrical.
You might need to alter the lock on your uPVC door for a variety of reasons. It is possible to replace the lock on your uPVC door due to many reasons.
A change in a uPVC locking mechanism can be done by anyone with basic DIY skills. If the lock is stuck, you'll need to check the hinges within the mechanism. If the hinges are greased then it is an easy fix. If you are not confident, it is best to seek out an expert.